The 2021 also offers a place to PnP a wired brake controller in the cable. The 2020s are prewired to the vehicle for plug and play (PnP) of 4-pin only, while the 2021 offers you the same connector but has a couple more wires giving the option of PnP for either 4-pin or 7-pin. If you pull the black box off behind the left rear bumper you will find a 12-pin connector that the harness connects to.
The other confusion is that ALL 20 Tellurides and Palisade are pre-wired. Introduced by John Deere for agricultural hardware, then used for other purposes, like yachts and general electric cables.Don’t confuse the brake controller harness which has 4 wires with the 4-pin flat trailer connector that goes on the back.
Tail lamps, clearance lamps/outline marker lamps and registration plate lamp A distinctive feature of the trailers that require this type of connector is the fact that they do not have their own braking system and stop along with the towing vehicle. It is less common on the U.S.-built vehicles, than 4-pin flat connector, but is still used in the older truck and SUV setups. This connector is available in some cases instead of the flat 4-pin connector. The following supplementary information exists for the connector:Ĥ-pin round connector (Towing vehicle side) SAE J560 was introduced in 1951, which means that older heavy duty vehicles (vintage) may have other connectors.Ĭlearance lamps/Outline marker lamps, Side marker lamps, identification lamps The brakes themselves are controlled using air pressure. SAE J560 is typically used on heavy duty trucks and trailers with pneumatic brakes where only the power to the ABS unit and indication of braking by brake light signal is required. Note that the SAE J560 connector is not controlling the brakes. It is also necessary to pay particular attention to pin 7.
The functional differences are small, but the difference in voltage and current requirements makes the SAE J560 and ISO 1185 incompatible without the use of additional equipment in the form of voltage converters. Some of the pins in the connector have also a slightly different function. The difference is that J560 indicates that the voltage must be 12V and that wire areas shall be larger due to the higher currents needed when using 12V compared to 24V. The plug for SAE J560 is physically identical to the connector ISO 1185. Physical design according to standard ISO 1185 / SAE J560. These converters usually don't handle the case of separate position light circuits for left and right side in the towing vehicle.ħ-pin trailer connector according to ISO 1185/SAE J560 (Towing vehicle side) What most of these converters do is to bring together the turn signals and stop lamp signal from a three-wire solution using 54, L and R into a two-wire solution using L54 and R54 according to DIN where brake light and turn indicator uses the same wire and bulb for each side. In market there are many special converters that solves the problem of connecting a car with European wiring to a trailer with North American wiring. If you have a trailer with a lot of lights the diode and relay wiring is preferred, but if you have a trailer with a simple light arrangement it is usually sufficient to wire to 58L. Note that the diodes have to be able to handle high currents or that they are used to control a relay which in turn feeds the trailer. If you want to be more advanced you can make a simple connection with two diodes that provide balanced load of the circuits. These two circuits shall not be merged because it can create problems in the towing vehicle. In case you have a vehicle that separates the left and right side position lights into 58L and 58R - like many German cars - it is advisable to choose 58L to feed the taillights. In some cases - as in the flat 4-pin or 5-pin connector - it is fairly obvious which color that is connected to which pin.
Note that different color coding can be used for certain functions, which means that you can not trust the colors mentioned here without measuring the contact and wiring from case to case. Heavy Vehicles are standardized through SAE J560 which is similar to ISO 1185. However, you can not be entirely sure until you have measured the current connector on the vehicle and trailer that they fit each other. On cars and light trucks (listed below as Light Vehicles) there is no formal standard, instead there is an accepted standard. In North American, but most commonly the USA market, it is very common for brake lights and turn signals to be combined.